ORTUR 32 bit Laser Master 2 Laser 15With7With20W Engraving Cutting Machine Printer

  

ORTUR 32 bit Laser Master 2 Laser 15W/7W/20W Engraving Cutting Machine Printer. NOTICE: WE ARE A VERIFIED SUPPLIER OF ORTUR PLEASE LOOK OUT FOR FAKES!!! AUTHENTIC 32 BIT LASER MASTER 2 ENGRAVER. Brief Introduction: The Laser Master 2 - 7W is good at picture engraving. The Laser Master 2 - 15W is the most cost-effective, available for both engraving and cutting.

The Laser Master 2 - 20W is higher power and supports a faster engraving and cutting. It could preprocess 32 instructions, support baud rate as high as 921600, more powerful! Main Features: Specialized Motherboard with STM32 MCU Ortur laser master firmware, smarter, faster, higher precision and easier to use.

The Most Advanced 32Bits Laser Engraver Firmware Laser power range could be S0 - S1000, compared to 8bits desktop laser engravers, which only has S0 - S255, Ortur Laser Master could control laser beam more accurately, could even use the high power laser unit to "draw" a picture on paper , that the 8bits high power laser engravers could not do. Engraving speed could be as high as 3000MM/Min. (If do not consider the laser carving result, the velocity of movement could be as high as 1000MM/S) Active Position Protection There is a G-sensor on the motherboard, if the machine detects unauthorized movement, the laser beam will stop. If laser engraver is under control, but users forget to operate and keep the laser beam working, extra safety will cut off in case the motor stopped moving, to prevent fire. Laser Beam Safety Guard If your computer system halted or USB cable disconnected, led to that the laser engraver stops moving, the laser beam will stop, to prevent fire. This laser engraver supports PWM mode. Exposure Duration Detection and Limitation LaserGRBL (free software) supports Windows XP, 7, 8, 10. LaserGRBL is the most popular carving software in the world, could import different format images, you could editing in PhotoShop, Inkscape, CAD, etc. And then connect to the engraver via laser LaserGRBL for engraving and cutting.

It's the most popular paid carving software in the world, very easy to use. Pre-assembled parts, just need 10 - 20 minutes to install the machine.

Aluminum profile frame + structured cabling, solid structure, smooth operation, attractive appearance 400 x 430 mm large engraving area. Specification: Synchronizing shaft mechanical structure, avoid out-sync on two Y rails, during full speed engraving. Electrical Power of Laser Module: 7W, 15W, 20W Motherboard: 32 bits motherboard with STM32 MCU Firmware: ORTUR Laser Master Firmware Please do not touch the laser emitter with your hand, or it may burn your hand.

Power of Laser Engraver: 36W, 12V 3A Wave Length: 445 ± 5nm Variable Focus: Yes Default Focal Length: 55MM for 15W & 20W Laser Module; 58MM for 7W Laser Module Input Format: NC, BMP, JPG, PNG, DXF, etc. Carving Area: X: 400MM x Y: 430MM Image size: No Limit (The pixel accuracy could be adjusted freely, and the default is 300 pixels per inch, it's about 0.81um pixel precision) Carving Speed: 3000MM / Min and less Note: This product is not recommended for industrial cutting due to its high engraving speed.

Please wear goggles when operating the laser engraver. Wear safety goggles to avoid blindness. Please avoid strong impact on the machine. Children under 14 are not allowed to use this product and children over 14 need adult supervision.

The light engraving machine can not be directly applied to any mirror reflecting object, which may cause injury to the operator or burn the laser. The item "ORTUR 32 bit Laser Master 2 Laser 15With7With20W Engraving Cutting Machine Printer" is in sale since Tuesday, December 22, 2020. This item is in the category "Crafts\Home Arts & Crafts\Woodworking\Wood Carving Hand Tools".

The seller is "goldeal-24-7" and is located in SHENZHEN . This item can be shipped worldwide.

• Fliament: Wood,Acrylic,etc
• Modified Item: No
• Custom Bundle: Yes
• California Prop 65 Warning: NO
• Consumables Diameter: 0MM
• Maximum Print Size: 400*430MM
• Printing Speed: 0-3,000MM/Min
• Molding Technology: FDM
• Motherboard: OLM V1.3 Motherboard
• Firmware: V1.34 Firmware
• Type: USB
• Motors: NEMA 17 Stepper Motors
• Mechanical Precision: Y:12.5um, X:12.5um
• Bed Temp: 0
• Pixel Accuracy: Adjustable
• MPN: Does Not Apply
• Default Focal Length: 58&55mm
• Control Mode: PWM
• Power Rate: S0-S1,000
• Slice Software: LaserGRBL, LightBurn
• Power Supply: 12V / 3A
• Maximum Working Speed: 0-3,000MM/Min
• Precision: 0.05-0.4MM
• Voltage: 110-220V
• Operating System: Win10 Mac and Linux
• File Format: BMP, JPG, PNG, etc
• Brand: ORTUR
• Nozzle Diameter: 0.4MM (Custom Options: 0.5/0.3/0.2MM)
• Diameter Temp: 0
• Verified: Seller
• Fast&Free: Shipping
• New: Edition
• Slice Thickness: 0MM
• CE Certification: Yes
• Language: English
• Auto Leveling: No
• Maximum Printing Speed: 0-3,000MM/Min