1 x USB Type-A to Type-A Cable. 1 x Ethernet to Ethernet Cable. 1 x Stainless Steel Clamp.
Engraving Depth: 0.25 in. Workbed Height Range: 9 in. Front/Back Pass Size: 25×1.46 in. Engraving Speed: 23.6 ips (600 mm/s).Cutting Speed: 15.7 ips (400 mm/s). Included Software: RDWorks 8, CorelLaser.
Graphic Operating Modes: Optimized Raster, Vector, and Combined. Transfer Interface: Flash Drive, USB Cord, Ethernet Cord. Machine Dimensions: 40.2×25.6×24.8 in. Laser Wavelength: 10.6 µm. Laser Tube Diameter: 2 in.Laser Tube Length: 34.6 in. If you must modify your. Special circumstances will be stated clearly in the listing. Please check everything carefully after you receive the parcel, as any damages except DOA (Dead-On-Arrival) are not covered if it's the fault of the consumer. Our 30-day Satisfaction Guarantee assures our customers that they will receive all orders promptly and exactly as described.
Parts must be resaleable and in the original packaging. We cannot take back used products. We cannot take back installed or tired products. We do reserve the right to refuse and return any parts we find have been installed, are used or do not meet the above criteria. Return request need to be within 30 days of receipt.
Combining ease of use with advanced capability, this intuitive 60W CO2 laser engraver delivers professional results at a fraction of the cost. Equipped with a powerful 60-watt water-cooled laser tube, high-precision stepper motor, and a top-quality Ruida LCD control board, it features our largest engraving surface (28" x 20") with a height-adjusting lift table and dual pass-through doors to accommodate oversized and irregular-shaped objects, making it one of our most highly capable engraving machines. Simply plug in the USB connector to your computer system and you're ready to start your laser engraving story! 60W CO2 laser tube with an estimated lifetime of up to 2,000 operation hours depending on power setting usage and water cooling performance.
PLEASE NOTE: Frequent use of high laser power settings will shorten the laser tube lifetime as follows. Low Power 10-40% = 1,700-2,000 Hours.Moderate Power 40-70% = 1,300-1,500 Hours. High Power 70-100% = 800-1,000 Hours.
Laser Cutting: Acrylic Wood Leather Plastics Fabrics MDF Cardboard Paper Corian Foam Fiberglass Rubber. Marking/Engraving: Acrylic Wood Leather Plastics Fabrics Glass Rubber Cork Brick Granite Marble Tile River Rock Bone Melamine Phenolic Aluminum Stainless Steel Titanium. Cannot cut hardwoods like mahogany.
CO2 lasers only mark bare metals when anodized or treated. Some PVC-based acrylics can create toxic fumes when lasered. The intuitive control panel with a digital display allows complete control of the laser head, pausing and stopping projects, adjusting laser power and speed settings, file viewing, and project framing via Windows-compatible RDWorks v8. Two-way pass allows you to feed material into the workbed from the front or back and cut materials larger than your bed size by sliding them through the cabinet. (500×700 mm) workbed gives you plenty of space to work on wood, rubber, plastic, paper, fabric, leather, ceramics, tile, fiberglass, marble, stone, and more-even before you open the integrated pass-through doors that permit you to work on even larger pieces!Our 1000 mm CO2 laser tube provides 60W of power for up to 2000 hours or lasts twice as long when consistently used at lower settings. A crystal-clear LCD display provides real-time information about the device's electric current and autocorrects faults, reducing damage to your laser tube and power supply in the rare case of improper ammeter connections. The transparent acrylic window's sepia filter allows you to observe your engraver in action, as the tint blocks the laser beam and protects your eyes. The laser automatically stops engraving, cutting, or marking when the workbed's cover is opened for your safety. Close the cover and press Start to resume your work. The E-Stop safety button immediately stops the machine in case of emergency.
1 x Venting Exhaust Duct 4 ft. 1 x USB Drive with Software 1 x Stainless Steel Clamp 10 x Hex Wrenches 1 x Double-sided Tape 1 x Power Cord 1 x Accessory Bag 2 x Keys 1 x Silicone Sealant 1 x Instruction Manual. MPN: MF2028-60 Model: SH-G570 Input Power: 110V/60Hz AC Processing Area: 20×28 in. (6 mm) Workbed Adjustment: Manual Workbed Height Range: 9 in.(230 mm) Front/Back Pass Size 32.87×3.94 in. Engraving Speed: 23.6 ips (600 mm/s) Max. Cutting Speed: 15.7 ips (400 mm/s) Included Software: RDWorks 8, CorelLaser Graphic Operating Modes: Optimized Raster, Vector, and Combined Transfer Interface: Flash Drive, USB Cord, Ethernet Cord Net Weight: 331 lb. (150 kg) Machine Dimensions: 47.2×34.3×36.6 in. Laser Tube Specs Rated Power: 60W Laser Tube Model: Laser Wavelength: 10.6 µm Laser Tube Diameter: 2 in.
(50 mm) Laser Tube Length: 39.4 in. Lens & Mirror Specs Focal Lens Diameter: 18 mm Focal Length: 2 in. (50.8 mm) Mirror Diameters: 25 mm. If the weight of your order exceeds 150 lbs. OMTech is a collaboration of 30-yr industry vets and promising new techs in Anaheim, California.Our affordable but quality lasers and US-based support quickly grew us into the largest online brand for precision engraving. Alongside our skilled & helpful staff, OMTech users have built up a supportive online family in our forums and social media, sharing inspiration and sharpening their DIY skills together. We love keeping the OMTech family on the cutting edge of laser crafting because we know our growth is inseparable from your success.
All emails will be responded to within 12-24 hours. One 45-minute Virtual Tech Support appointment with OMTech Specialists in Anaheim, California. This item is in the category "Business & Industrial\Printing & Graphic Arts\Screen & Specialty Printing\Engraving".The seller is "orionmotortech" and is located in this country: US. This item can be shipped to United States.